EEEEnnnngggglllliiiisssshhhh 323P4 325P5 X-series Operator’s manual (EPA) Please read the operator’s manual carefully and make sure youunderstand t
10 – EnglishSAFETY INSTRUCTIONS- Use the combination spanner to tighten the blade nut while holding up the tip of the bar. Check that you can pull the
English – 11SAFETY INSTRUCTIONS• Whether rivets and links are badly worn.We recommend you compare the existing chain with a new chain to decide how ba
12 – EnglishSAFETY INSTRUCTIONS• Place the machine on the ground, ensure the cutting attachment is clear of twigs and stones. Hold the body of the mac
English – 13SAFETY INSTRUCTIONSSafety instructions while working• Always ensure you have a safe and stable working position• Always use both hands to
14 – EnglishSAFETY INSTRUCTIONS• Whenever possible position yourself so that you can make the cut at right angles to the branch.• Do not work with the
English – 15WHAT IS WHAT?What is what?272823242119221817131514175104202323262511121630323129689231 Grease filler cap2 Bevel gear3 Chain lubrication adj
16 – EnglishASSEMBLYFitting the cutting head• Fit the cutting head on the shaft so that the screw (A) is aligned with the hole in the shaft as shown.•
English – 17ASSEMBLYAssembling and dismantling the two-piece shaft(325P5)Assembly:• Make sure the knob is loose.• Align the cut-out in the upper shaft
18 – EnglishFUEL HANDLINGFuelCAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-st
English – 19STARTING AND STOPPINGCheck before starting• Inspect the working area. Remove any objects that could be thrown out.• Check the cutting atta
2 – English KEY TO SYMBOLS Symbols WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fatal
20 – EnglishMAINTENANCECarburettorYour Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the
English – 21MAINTENANCEFine adjustment of the idle speed TAdjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. Fir
22 – EnglishMAINTENANCECAUTION! Never use a machine with a defective muffler.Cooling systemTo keep the working temperature as low as possible the mach
English – 23MAINTENANCEOiling the air filterAlways use HUSQVARNA filter oil, art. no. 503 47 73-01. The filter oil contains a solvent to make it spread e
24 – EnglishTECHNICAL DATATechnical dataNote 1: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure lev
English – 25TECHNICAL DATA Bar and chain combinationsThe following combinations are CE approved.Bar ChainLength, inches Pitch, inchMax. no of teeth on
26 – EnglishFEDERAL EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS AND OBLIGATIONSThe EPA (The US Environmental Protection Agency), Environme
English – 3 CONTENTS Contents Note the following before starting: The machine is only designed for cutting branches and twigs.Maintenance, replaceme
´®z+H0o¶5M¨´®z+H0o¶5M¨
´®z+H0o¶5M¨2003-03-19´®z+H0o¶5M¨1140167-95
4 – English SAFETY INSTRUCTIONS Personal protective equipment GLOVESGloves must be worn when required, for example when fitting, inspecting or cleani
English – 5 SAFETY INSTRUCTIONS The machine ′ s vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment
6 – English SAFETY INSTRUCTIONS • See instructions under the heading Start. Start the machine and apply full throttle. Release the throttle and chec
English – 7 SAFETY INSTRUCTIONS • Keep cutting equipment well lubricated and properly maintained! A poorly lubricated chain is more likely to brea
8 – English SAFETY INSTRUCTIONS • The cutting part of the chain is called the cutting link and this consists of a cutting tooth (A) and the raker li
English – 9 SAFETY INSTRUCTIONS • File all the teeth to the same length. When the length of the cutting teeth is reduced to 4 mm (0.16") the ch
Commentaires sur ces manuels