Husqvarna 326RX-Series Manuel d'utilisateur

EEEEnnnngggglllliiiisssshhhh 326R X-SERIES Operator ′ s manual Please read the operator’s manual carefully and make sure youunderstand the instructi

10 – English SAFETY INSTRUCTIONS General rules Only use cutting attachments with the guards we recommend! See the chapter on Technical data.Keep the

English – 11 SAFETY INSTRUCTIONS Adjust the blade setting. This should be 1 mm. Trimmer head • Only use the recommended trimmer heads and trimmer co

12 – English ASSEMBLY Fitting the handlebar • Remove the screw at the rear of the throttle handle.• Slide the throttle handle onto the right side of

English – 13ASSEMBLY• Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.• Insert th

14 – EnglishASSEMBLYFitting a trimmer guard and Superauto II 1” trimmer head• Fit the correct trimmer guard (A) for use with the trimmer head. Hook th

English – 15ASSEMBLYAdjusting the harness and clearing sawStandard harnessQuick releaseAt the front is an easily accessible, quick release. Use this i

16 – EnglishFUEL HANDLINGFuel safetyNever start the machine:1 If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporat

English – 17FUEL HANDLINGMixing• Always mix the petrol and oil in a clean container intended for fuel.• Always start by filling half the amount of the

18 – EnglishSTARTING AND STOPPINGCheck before starting• Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the cent

English – 19STARTING AND STOPPINGCAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully

2 – English KEY TO SYMBOLS Symbols WARNING! Careless or incorrect use can result in serious or fatal injury to the operator or others.Please read th

20 – EnglishWORKING TECHNIQUESGeneral working instructionsBasic safety rules1 Look around you:• To ensure that people, animals or other things cannot

English – 21WORKING TECHNIQUES• Start at whichever end of the area is easiest, and clear an open space from which to work.• Work systematically to and

22 – EnglishWORKING TECHNIQUESBrush cutting with a saw blade• Thin stems and brush are mown down. Work with a sawing movement, swinging sideways.• Try

English – 23WORKING TECHNIQUES• Do not allow the trimmer head to constantly come into contact with the ground during normal cutting. Constant contact

24 – EnglishMAINTENANCECarburettorYour Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the

English – 25MAINTENANCEwill run smoothly in every position. The idle speed should also be well below the speed at which the cutting attachment starts

26 – EnglishMAINTENANCEshould be cleaned weekly, or replaced if necessary. On mufflers fitted with a catalytic converter the mesh should be checked, and

English – 27MAINTENANCEOiling the air filterAlways use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread e

28 – EnglishMAINTENANCEMaintenance scheduleThe following is a list of the maintenance that must be performed on the machine. Most of the items are des

English – 29TECHNICAL DATATechnical dataNote 1: Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive 2000/

English – 3 CONTENTS Contents Note the following before starting: Husqvarna AB has a policy of continuous product development and therefore reserves

30 – EnglishTECHNICAL DATAEC-declaration of conformity(Applies to Europe only)We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, decl

1Super Auto IISuper Auto II 123456789104,0 m 13'2,4 mm.095"~2,0 m6,5'6"6""15 cm15 cm

"Clic"12356710118,5 m28'484,2 m14'2,4-2,7 mm.095-.106"10 cm 4"6"15 cmS35

´®z+HA"¶6x¨´®z+HA"¶6x¨12432,4-2,7 mm.095-.106"4,25 m14'4,25 m14'B6"15 cmA6"15 cmS355

T35"Clic"12356798,5 m28'484,3 m14'2,4-2,7 mm.095-.106"10 cm 4"6"15 cm

´®z+HA"¶6x¨2004-10-07´®z+HA"¶6x¨1140330-26

4 – English INTRODUCTION Dear Customer, Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back

English – 5 WHAT IS WHAT? What is what? 1 Blade2 Grease filler cap, bevel gear3 Bevel gear4 Cutting attachment guard5 Shaft6 Handlebar7 Throttle cont

6 – English SAFETY INSTRUCTIONS Important Personal protective equipment HELMETA helmet should be worn if the trees being cleared are taller than 2 m

English – 7 SAFETY INSTRUCTIONS CLOTHINGWear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always w

8 – English SAFETY INSTRUCTIONS Cutting attachment guard This guard is intended to prevent loose objects from being thrown towards the operator. The

English – 9 SAFETY INSTRUCTIONS If the muffler on your machine is fitted with a spark arrestor mesh this must be cleaned regularly. A blocked mesh wil