EEEEnnnngggglllliiiisssshhhh 323P4 325P5 X-series Operator’s manual (EPA) Please read the operator’s manual carefully and make sure youunderstand t
10 – English GENERAL SAFETY PRECAUTIONS Sharpening your chain and adjusting raker clearance General information on sharpening cutting teeth • Never
English – 11 GENERAL SAFETY PRECAUTIONS • File all the teeth to the same length. When the length of the cutting teeth is reduced to 4 mm (0.16"
12 – English GENERAL SAFETY PRECAUTIONS - Tighten the bar nut using the combination spanner. Check that the chain can be pulled round easily by hand
English – 13GENERAL SAFETY PRECAUTIONSChecking wear on cutting equipmentChainCheck the chain daily for:• Visible cracks in rivets and links.• Whether
14 – EnglishASSEMBLYFitting the cutting head• Fit the cutting head on the shaft so that the screw (A) is aligned with the hole in the shaft as shown.•
English – 15ASSEMBLY• Tighten the knob.Dismantling:Undo the knob (at least three turns).• Push the knob towards the coupling.• Carefully twist the upp
16 – EnglishFUEL HANDLINGFuel safetyNever start the machine:1 If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporat
English – 17FUEL HANDLINGMixing• Always mix the gasoline and oil in a clean container intended for fuel.• Always start by filling half the amount of th
18 – EnglishSTARTING AND STOPPINGCheck before starting• Inspect the working area. Remove any objects that could be thrown out.• Check the cutting atta
English – 19STARTING AND STOPPINGStartingHold the body of the machine on the ground using your left hand (CAUTION! Not with your foot!). Grip the star
2 – English KEY TO SYMBOLS Symbols WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fatal
20 – EnglishWORKING TECHNIQUESGeneral working instructionsPersonal protection• Always wear boots and other equipment described under the heading Perso
English – 21WORKING TECHNIQUESSafety instructions after completing work• The transport guard should always be fitted to the cutting attachment when the
22 – EnglishWORKING TECHNIQUES• Never cut through the swelling at the root of the branch as this will slow down healing and increase the risk of funga
English – 23MAINTENANCECarburetorYour Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the e
24 – EnglishMAINTENANCEFine adjustment of the idle speed TAdjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. Fir
English – 25MAINTENANCEOn mufflers without a catalytic converter the mesh should be cleaned weekly, or replaced if necessary. On mufflers fitted with a c
26 – EnglishMAINTENANCECleaning the air filterRemove the air filter cover and take out the filter. Wash it clean in warm, soapy water. Ensure that the fil
English – 27MAINTENANCEMaintenance scheduleThe following is a list of the maintenance that must be performed on the machine. Most of the items are des
28 – EnglishTECHNICAL DATATechnical dataNote 1: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure lev
English – 29TECHNICAL DATABar and chain combinationsThe following combinations are CE approved.Bar ChainLength, inch Pitch, inchMax. no of teeth on ti
English – 3 CONTENTS Contents Note the following before starting: Please read the operator’s manual carefully.Long-term exposure to noise can result
30 – EnglishFEDERAL EMISSION CONTROL WARRANTY STATEMENT´®z+HB3¶5t¨´®z+HB3¶5t¨YOUR WARRANTY RIGHTS AND OBLIGATIONSThe EPA (The US Environmental Protect
´®z+HB3¶5t¨2005-01-04´®z+HB3¶5t¨1140341-95
4 – English INTRODUCTION Dear customer! Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back
English – 5 WHAT IS WHAT? What is what?1514101211142717232323228913292826356212725242019181630 1 Chain lubrication adjustment screw2 Shaft3 Front ha
6 – English GENERAL SAFETY PRECAUTIONS ImportantPersonal protective equipment PROTECTIVE HELMET AND VISORHEARING PROTECTIONWear hearing protection t
English – 7 GENERAL SAFETY PRECAUTIONS Machine ′′′′ s safety equipment This section describes the machine ′ s safety equipment, its purpose, and ho
8 – English GENERAL SAFETY PRECAUTIONS The machine ′ s vibration damping system reduces the transfer of vibration between the engine unit/cutting eq
English – 9 GENERAL SAFETY PRECAUTIONS • Keep the chain’s cutting teeth properly sharpened! Follow our instructions and use the recommended file gau
Commentaires sur ces manuels