Husqvarna 8024ST Manuel d'utilisateur télécharger pdf (Page 18)

STORAGE

Immediately prepare your snow thrower for storage at the

end of the season or if the unit will not be used for 30 days

or more.

WARNING: Never store the snow

thrower with gasoline in the tank inside

a building where fumes may reach an

open flame, spark or pilot light as on a

furnace, water heater, clothes dryer or

gas appliance. Allow the engine to cool

before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time,

clean it thoroughly, remove all dirt, grease, leaves, etc.

Store in a clean, dry area.

1. Clean entire snow thrower (See “CLEANING” in the

Maintenance section of this manual).

2. Inspect and replace belts, if necessary (See “TO RE-

PLACE BELTS” in the Service and Adjustments sec-

tion of this manual).

3. Lubricate as shown in the Maintenance section of this

manual.

4. Be sure that all nuts, bolts, screws, and pins are

securely fastened. Inspect moving parts for damage,

breakage and wear. Replace if necessary.

5. Touch up all rusted or chipped paint surfaces; sand

lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from

forming in essential fuel system parts such as carburetor,

fuel hose, or tank during storage. Also, alcohol blended

fuels (called gasohol or using ethanol or methanol) can

attract moisture which leads to separation and formation of

acids during storage. Acidic gas can damage the fuel

system of an engine while in storage.

1. Drain the fuel tank.

2. Start the engine and let it run until the fuel lines and

carburetor are empty.

• Never use engine or carburetor cleaner products in the

fuel tank or permanent damage may occur.

• Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in

minimizing the formation of fuel gum deposits during stor-

age. Add stabilizer to gasoline in fuel tank or storage

container. Always follow the mix ratio found on stabilizer

container. Run engine at least 10 minutes after adding

stabilizer to allow the stabilizer to reach the carburetor. Do

not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine

oil. (See “ENGINE” in the Maintenance section of this

manual).

CYLINDER

1. Remove spark plug.

2. Pour one ounce (29 ml) of oil through spark plug hole

into cylinder.

3. Pull recoil starter handle slowly a few times to distribute

oil.

4. Replace with new spark plug.

OTHER

• Do not store gasoline from one season to another.

• Replace your gasoline can if your can starts to rust.

Rust and/or dirt in your gasoline will cause problems.

• If possible, store your snow thrower indoors and cover

it to protect it from dust and dirt.

• Cover your snow thrower with a suitable protective

cover that does not retain moisture. Do not use plastic.

Plastic cannot breathe, which allows condensation to

form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/

exhaust area is still warm.

NOTE: To seal punctures or prevent flat tires due to slow

leaks, tire sealant may be purchased from your local parts

dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance

should not be affected at altitudes up to 7,000 feet (2,134

meters). If your engine does not operate properly due to

suspected carburetor problems, take your snow thrower to

a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set

for proper engine speed. Overspeeding the engine above

the factory high speed setting can be dangerous and will

void the warranty. If you think the engine-governed high

speed needs adjusting, contact a qualified service center,

which has proper equipment and experience to make any

necessary adjustments.

TO REMOVE WHEELS

• Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the

innermost hole in axle and the wheel hub hole. To disen-

gage drive system from the wheels (for pushing or trans-

porting the snow thrower), remove klik pin from wheel hub

and insert pin into the outermost hole in axle only.

INNER

HOLE

KLIK PIN

OUTER HOLE

WHEEL HUBWHEEL

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

Husqvarna 8024ST Manuel d'utilisateur Page 18

Commentaires sur ces manuels

Produits connexes et manuels pour Machines spéciales Husqvarna 8024ST