Husqvarna 5524SEB Manuel d'utilisateur

5524SEBOwner's Manual

10TO MOVE FORWARD AND BACKWARD (See Fig. 16)SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction drive con

11TO ADJUST SKID PLATES (See Fig. 17)NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.Skid plates are located on each

12COLD START - ELECTRIC STARTER1. Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. DO NOT turn the k

13MAINTENANCELUBRICATION CHARTGENERAL REC OMMENDA TIONSThe warranty on this snow thrower does not cover items that have been sub jected to operator ab

14MAINTENANCEV-BELTSCheck V-belts for deterioration and wear after every 50 hours of operation and replace if necessary. The belts are not ad justable

15SERVICE AND ADJUSTMENTSWARNING: To avoid serious injury, before performing any service or ad-justments:1. Be sure throttle is in STOP position.2. Re

16SERVICE AND ADJUSTMENTSTO REPLACE BELTS (See Fig. 21)The auger and traction drive belts are not adjustable. If the belts are damaged or begin to sli

17STORAGEImmediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.WARNING: Never

18Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equi

19SERVICE NOTES

2IMPORTANTSafe Operation Practices for Walk-Behind Snow ThrowersThis snow thrower is capable of amputating hands and feet and throwing objects.Failure

20REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLYSNOW THROWER - MODEL NO. 5224SEB (96193001000), PRODUCT NO. 961 93 0

21KEY PART NO. NO. DESCRIPTION 4 532 19 10-79 Pulley, Impeller 5 532 18 89-09 Bearing Assembly, F

22REPAIR PARTS CONTROL PANEL / DISCHARGE CHUTESNOW THROWER - MODEL NO. 5224SEB (96193001000), PRODUCT NO. 961 93

23KEY PART NO. NO. DESCRIPTION 1 532 18 33-34 Knob, Lever 2 817 50 10-10 Screw #10-24 x 5/8 3

24REPAIR PARTS HANDLESSNOW THROWER - MODEL NO. 5224SEB (96193

25KEY PART NO. NO. DESCRIPTION 1 532 18 41-10 Lever, Auger Control, RH 2 532 18 41-09 Lever, Trac

26REPAIR PARTS DRIVESNOW THROWER - MODEL NO. 5224SEB (

27KEY PART NO. NO. DESCRIPTION 1 532 14 63-15 Screw, Hex Head 5/16-18 x 5/8 2 873 80 05-00 Nut,

28REPAIR PARTS CHASSIS / ENGINE / PULLEYSSNOW THROWER - MODEL NO. 5224SEB (96193001000), PRODUCT

29KEY PART NO. NO. DESCRIPTION 1 532 18 10-44 Spring, Traction Idler 2 532 18 05-22 Pulley, Idler (2-1/4

3CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and man ufac-tured to give best possible dependability and

30REPAIR PARTS WHEELS / DECALSSNOW THROWER - MODEL NO. 5224SEB (96193001000),

31KEY PART NO. NO. DESCRIPTION 1 532 18 78-31 Wheel Assembly, 13", LH 2 532 15 54-43 Pin, Kl

532 40 37-59 12.19.05 BY Printed in U.S.A.SECTION 1: LIMITED WARRANTY Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna

4PARTS PACKED SEPARATELY IN CARTONRead these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thro

5ASSEMBLY / PRE-OPERATIONNOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making ad justments to the skid

6ASSEMBLY / PRE-OPERATIONINSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD (See Fig. 7)NOTE: The multi-wrench provided in your parts bag may be used to ins

7OPERATIONKNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with

8OPERATIONChoke control - used for starting a cold engine.Drive speed control lever - used to select forward or reverse motion and speed of snow throw

9The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glas