Husqvarna E-tech 325P4 Manuel d'utilisateur

325P4X-SERIESOperator's manual (EPA)Read through the Operator‘s Manual carefully andunderstand the content before using the machine.101 90 36-95

10 – EnglishSAFETY INSTRUCTIONSD. Adjusting raker clearance• When correction of theraker clearance is madethe teeth must be newlysharpened.We recommen

English – 11Checking wear on cutting equipmentA. Saw chainCheck the saw chain dailyfor:• Visible cracks in rivetsand links.• Whether the chain is stif

12 – EnglishSAFETY INSTRUCTIONSGeneral safety instructionsTransport and storage• Store and transport the machine and fuel so that any leakageor fumes

English – 13SAFETY INSTRUCTIONSSafety instructions when using themachine!Protective instructions while working• Always ensure you have asafe and firm

14 – English!Basic working techniques• The machine should beheld as close to the bodyas possible to get the bestbalance.• Make sure that the tipdoes n

English – 15• Use the stop at the base ofthe bar to provide supportduring cutting. This willhelp prevent the cuttingequipment from jumpingon the branc

16 – EnglishWHAT IS WHAT?What is what on the machine?272928252323262324211922181711121316151417510420689231. Lubricant filler hole2. Bevel gearbox3. C

English – 17ASSEMBLYFitting the cutting head• Fit the cutting head onthe shaft so that the screw(A) is aligned with thehole in the shaft asshown.• Tig

18 – EnglishFUEL HANDLINGFuel mixture!WARNING!Always provide good ventilation whenhandling fuel.NOTE!The machine is fitted with a two-stroke engine an

English – 19START AND STOPCold engineIGNITION:Set the stop switch to thestart position.CHOKE:Set the choke control in thechoke position.AIR PURGE:Pres

2 – EnglishSymbolsSYMBOL EXPLANATIONWARNING! This machine can bedangerous. Careless or incorrect usecan result in serious or fatal injury tothe operat

20 – EnglishFine adjustment• When the machine has been ”run-in” the carburetor shouldbe finely adjusted. The fine adjustment should be carriedout by q

English – 21Correctly adjusted carburetorA correctly adjusted carburetor means that the machineaccelerates without hesitation and the machine 4-cycles

22 – EnglishMAINTENANCECooling systemTo maintain as low opera-ting temperature as possiblethe engine is equipped witha cooling system.The cooling syst

English – 23MAINTENANCENOTE: Use only HUSQVARNA replacement parts. Use ofother brands of replacement parts can cause damage to yourunit or injury to t

24 – EnglishTECHNICAL DATA325P41,50/24,51,34/341,06/27125002 7000,9 kW/ 9 000 rpmYesYesWalbro MBNGK BPMR 7A0,02/0,5Zama C1Q1,06/0,50,36/0,1711,2/5,192

English – 2515L Type Inch Inch/mm Inch/mm Angle Angle Angle Inch/mm Inch/cm: dl 91VG 3/8" 0,050"/1,3 5/32" /4,0 85° 30° 0° 0,025"/

26 – English´*3#e¶5B¨EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS ANDOBLIGATIONSThe EPA (The US Environmental Protection Agency),Environmen

2001W02´*3#e¶5B¨

English – 3CONTENTSList of contentsSYMBOL EXPLANATIONSymbols ... 2CONTENTS

4 – EnglishThe machine‘s safety equipmentThis section describes the machine‘s safety equipment, itsfunction and how checks and maintenance are carried

English – 5SAFETY INSTRUCTIONS3. Vibrationdamping systemYour machine is equippedwith a vibration dampingsystem, which is designedto give as vibration-

6 – EnglishSAFETY INSTRUCTIONSInspecting, maintaining andservicing machine safety equipmentIMPORTANT INFORMATION• All service and repairs to the machi

English – 7SAFETY INSTRUCTIONSWARNING!Never use a machine with defectivesafety equipment. The safety equipmentshould be maintained as described in thi

8 – EnglishSAFETY INSTRUCTIONSSaw chain• Saw chain pitch (inches)Spacing between drivelinks.• Drive link width (mm/inches).• Number of drive links.• L

English – 9SAFETY INSTRUCTIONSB. Sharpeningcutting toothTo sharpen cutting teeth youwill need a ROUND FILEand a FILE GAUGE.1. Check that the chain isc