Husqvarna 326HDA Manuel d'utilisateur

EEEEnnnngggglllliiiisssshhhh 326HDA X-series 326HE3 X-series 326HE4 X-series Operator ′ s manual Please read the operator’s manual carefully and m

10 – English SAFETY INSTRUCTIONS Safety instructions while working • Always ensure you have a safe and stable working position• Always use both hand

English – 11SAFETY INSTRUCTIONSChanging the hedge trimmer angle(326HE3, 326HE4)• Undo the knob.• Grasp the handle on the angle stop, adjust to the des

12 – EnglishWHAT IS WHAT?What is what?819121314171615182227252623115212046219102317326HE4326HDA5524281 Cutter2 Grease nipples (3)3 Bevel gear4 Cutter

English – 13ASSEMBLYFitting the hand guard and loop handle(326HDA55/326HE3)1 Assemble the hand guard and loop handle by screwing them together. Take c

14 – EnglishFUEL HANDLINGFuelCAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of petrol and two-stro

English – 15FUEL HANDLINGFuelling• Clean the area around the fuel cap. Contamination in the tank can cause operating problems.• Ensure that the fuel i

16 – EnglishSTARTING AND STOPPINGCheck before starting• Inspect the working area. Remove any objects that could be thrown out.• Check the cutting atta

English – 17STARTING AND STOPPINGHold the body of the machine on the ground using your left hand (CAUTION! Not with your foot!). Grip the starter hand

18 – EnglishMAINTENANCECarburettorYour Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the

English – 19MAINTENANCEHigh speed jet HThe high speed jet H affects the engine power, speed, temperature and fuel consumption. If the high speed jet H

2 – English KEY TO SYMBOLS Symbols WARNING! Hedge trimmers can be dangerous! Careless or incorrect use can result in serious, even fatal injury.Plea

20 – EnglishMAINTENANCECooling systemTo keep the working temperature as low as possible the machine is equipped with a cooling system.The cooling syst

English – 21MAINTENANCEGear housingThere are three grease nipples on the gear housing. Use a grease gun to top up with grease. This should be carried

22 – EnglishTECHNICAL DATA´®z+H4"¶67¨´®z+H4"¶67¨Technical dataNote 1: Noise emissions in the environment measured as sound power (LWA) in co

English – 23TECHNICAL DATAEC-declaration of conformity(Applies to Europe only)Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare u

´®z+H4"¶67¨2003-09-15´®z+H4"¶67¨1140200-26

English – 3 CONTENTS Contents Note the following before starting: Husqvarna AB has a policy of continuous product development and therefore reserves

4 – English SAFETY INSTRUCTIONS Personal protective equipment GLOVESGloves must be worn when required, for example when fitting, inspecting or cleani

English – 5 SAFETY INSTRUCTIONS Vibration damping system Your machine is equipped with a vibration damping system that is designed to minimise vibra

6 – English SAFETY INSTRUCTIONS Checking, maintaining and servicing the machine ′′′′ s safety equipment Throttle lock • Make sure the throttle cont

English – 7 SAFETY INSTRUCTIONS Vibration damping system • Regularly check the vibration damping units for cracks or deformation.• Check that the vi

8 – English SAFETY INSTRUCTIONS Cutter guard (326HDA55) • Check that the blade guard is not damaged or distorted.• Replace the blade guard if it is

English – 9 SAFETY INSTRUCTIONS Fuel safety • Always use a fuel container with an anti-spill valve.• Never refuel the machine while the engine is ru